... The Dreams Cant Be More Real Then That ... Dreams can come true
    Top » Catalog » Mini TS  |     Tuesday 18 December, 2018        

Currency
Change to GBP Currency
Change to EURO Currency
Change to US Dollar Currency
Categories
.: Israel Cars
.: SCALE / MASHTAB+
.: Autos / Cars+
.: TRUCKS & Bus
.: MotorCycle
.: EAST Europe Cars
.: Vehicle Manufacturers+
.: Movies
.: Military
.: Classics up to 1950's
.: Designs accessories
.: Gliders
.: Scratch & Dent
Enter Shop

Email : 

Pass :

Registration
Forgot Pass
SEARCH BY BRAND
What's New? more
1/18 CMC Auto Union Typ D #12, 1938/39 French GP 1939
1/18 CMC Auto Union Typ D #12, 1938/39 French GP 1939
469.40$

---------
1/18 CMC MERCEDES-BENZ W 196 R #16, STIRLING MOSS, GP MONZA 1955
1/18 CMC MERCEDES-BENZ W 196 R #16, STIRLING MOSS, GP MONZA 1955
3,779.10$

---------
1/18 CMC Mercedes-Benz 300 SLR, Mille Miglia #722, 1955 sign. Si
1/18 CMC Mercedes-Benz 300 SLR, Mille Miglia #722, 1955 sign. Si
3,779.10$

---------
1/18 CMC Maserati Tipo 61 Birdcage, 1960, sign.מזראטי  Dan Gurne
1/18 CMC Maserati Tipo 61 Birdcage, 1960, sign.מזראטי Dan Gurne
3,779.10$

---------
1/18 CMC MERCEDES-BENZ SSKL, ANNIVERSARY MODEL 15 YEARS
1/18 CMC MERCEDES-BENZ SSKL, ANNIVERSARY MODEL 15 YEARS
1,690.65$

---------
1/43 NSU 1000 L - 1964 - WHITE L.E. 744 pcs.
1/43 NSU 1000 L - 1964 - WHITE L.E. 744 pcs.
76.42$

---------
Payment

Thanks to
האתר_לחיפוש_מוסכים_ושרותי_רכב
Currencies
Mini TS Mini TS

Mini TopSky Installation Manual

Attention: Because after the compound materials solidify, there will be ammonia iris on the surface, which affect the bonding strength afterwards. Please polish with sandpaper on all bonding surface.

 

Draw a line on the table

sand the edge of the tail balsa

 

Sand the gap for the hinge

lightly sand the face of the balsa with more fine sandpaper

Bond the fiberglass cloth into the tail balsa with 30min Z-poxy

cover the one side of  the tail with film

folding the tail and cover the other side

Cut the covering of the tail

Sand the top surface of stabilizer mount, make sure it’s vertical to the side surface.

Sand the side surface, or you can make streamline as shown in the picture below.

Cover the tail boom with 300# sandpaper, then sand the groove of the stabilizer mount. Make sure that the groove is parallel to the fuselage, and parallel to the outside surface of the tail boom.

And after bond to the tail boom, the upper side of the mount should be parallel to the central line of the tail boom.

Fix the tail on your working board. Check the joint:

l         The stabilizer is parallel to the center line of the tail boom, or it may have an angle of -1 degree.

l         The hinge of the elevator is vertical to the tail boom.

l         The center line of the tail boom is right in the middle of the stabilizer.

l         The vertical tail is vertical to the stabilizer.

l         The vertical tail is on the same surface as the center line of the fuselage.

l         The hinge of the vertical tail is vertical to the center line of the tail boom.

Temporarily joint the vertical tail and the tail boom with C.A(ZAP)

bond the tail boom and the vertical tail from both side using fiberglass and epoxy. There is fiberglass in the accessories. And e-proxy 30min is recommended . When the  epoxy is solidify,  cut the unwanted fiberglass.

fix the screw on the fuselage ,and join the wing . draw line on the wing at both side of the screw

cut the foam

fill the hole wth 6min epoxy

when the epoxy is solidify, filing semi-circle slot on the epoxy

Temporarily join the wing on the workboard

two tips are 88mm higher than the working board (at the trailing edge of the wing)

Put Paper Adhesive Sticker on the joint of the wing bottom, and glue the wing with 6min epoxy on the platform.

bond the wing with fiberglass and 30min epoxy

bond the carbon cloth into the wing. 30min epoxy is recommended

bond the carbon cloth for finger peg

when epoxy is solidify, cut the hole on the carbon

join the wing on the fuselage, check hole is right or not

Drill 4mm screw holes

install the finger peg

Drill hole on the rear part of the fuselage, preparing for the linkage of the tail

sand the end of the fuselage

Assemble the wing on the fuselage, temporarily join the fuselage and boom

Bond the fuselage and the tail boom with 30min epoxy

Rotate the tail boom, make sure the stabilizer is horizontal

Waiting for the solidify

turn the receiver power on, and servo come back to zero position

drill hole on the servo mount, and  install the servo with screw

cut 4 pieces 5mm balsa

drill hole

and glue the balsa and tube with ZAP C.A

cut the balsa as the photo

install the tube with steel wire

glue the tube balsa on the servo mount with C.A (ZAP)

cut the horn

cut slot on the rudder

and on the elevator

insert the  horn, and adjust to appropriate position

straighten the tube , and bond the end of  the tube with Adhesive Sticker

cover the tube with table

turn the receiver power on

Make a Z bend on the wire with pliers. Reinstall the horns with wires connected .

Power on the receiver, center the servo

glue the horns on the control surface with fast glue

fix the horn with 30min epoxy

ok , stay mini in car all the time

 


Continue
Quick Research
Keyword:
Price Between:
and
Search in:
Manufactured by:
Shopping Cart more
0 items
Contact
Continue
Specials more
1/43 EG SDKFZ 251 - Germany 1941
1/43 EG SDKFZ 251 - Germany 1941
54.96$
32.98$
מבצעים נוספים  
Bestsellers
01.1/43 EG LAV 25 PIRANAH - U.S. 1991
02.1/43 EG SDKFZ 251 - Germany 1941
03.1/43 IXO Ferrari 250 GT California 1957 Red
04.1/43 IXO Mercedes-Benz SSK 1928 White
05.1/43 IXO CITROEN AX K-Way (Serie Speciale) 1988 White
06.1/43 IXO Lancia Aurelia B20
07.1/43 IXO Lincoln Continental 1939 Green with Beige Interiors
08.1/43 JC LEXUS RX 400h 2006 Silver Metallic
Information
Shipping & ReturnsShipping & Returns
Privacy NoticePrivacy Notice
Conditions of UseConditions of Use
Contact UsContact Us
[ 2004 © oToSale.com All Rights Reserved ]
[ Rules | Shipping & Returns | Privacy | Contact Us ]
[ Powered By The Exchange Project ]